This image was saved from this machine with hard drive S.M.A.R.T. info at 2024-10-26-2245
*****************************************************.
For the drive: /dev/sda
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-41-generic] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba 2.5" HDD (30-60 GB)
Device Model:     TOSHIBA MK6034GSX
Serial Number:    96LV1249S
Firmware Version: AH101M
User Capacity:    60,011,642,880 bytes [60.0 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database 7.3/5528
ATA Version is:   ATA/ATAPI-7 (minor revision not indicated)
Local Time is:    Sat Oct 26 22:45:23 2024 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(  219) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  43) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   050    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   050    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0027   100   100   001    Pre-fail  Always       -       1008
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       4044
  5 Reallocated_Sector_Ct   0x0033   100   100   050    Pre-fail  Always       -       67
  7 Seek_Error_Rate         0x000b   100   100   050    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   050    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0032   075   075   000    Old_age   Always       -       10317
 10 Spin_Retry_Count        0x0033   180   100   030    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       4026
192 Power-Off_Retract_Count 0x0032   099   099   000    Old_age   Always       -       621
193 Load_Cycle_Count        0x0032   075   075   000    Old_age   Always       -       252086
194 Temperature_Celsius     0x0022   100   100   000    Old_age   Always       -       39 (Min/Max 11/61)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       33
197 Current_Pending_Sector  0x0032   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
220 Disk_Shift              0x0002   100   100   000    Old_age   Always       -       127
222 Loaded_Hours            0x0032   079   079   000    Old_age   Always       -       8767
223 Load_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
224 Load_Friction           0x0022   100   100   000    Old_age   Always       -       0
226 Load-in_Time            0x0026   100   100   000    Old_age   Always       -       382
240 Head_Flying_Hours       0x0001   100   100   001    Pre-fail  Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 11 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 11 occurred at disk power-on lifetime: 8483 hours (353 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 04 74 d0 60 e0  Error: UNC 4 sectors at LBA = 0x0060d074 = 6344820

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 70 d0 60 e0 00      00:25:54.777  READ DMA
  c8 00 08 c0 85 7a e1 00      00:25:54.777  READ DMA
  c8 00 08 48 75 75 e1 00      00:25:54.777  READ DMA
  c8 00 08 e8 d7 72 e1 00      00:25:54.763  READ DMA
  c8 00 08 f0 39 72 e1 00      00:25:54.752  READ DMA

Error 10 occurred at disk power-on lifetime: 8483 hours (353 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 04 74 d0 60 e0  Error: UNC 4 sectors at LBA = 0x0060d074 = 6344820

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 70 d0 60 e0 00      00:22:23.161  READ DMA
  c8 00 08 a0 0c 74 e1 00      00:22:23.151  READ DMA
  c8 00 08 90 0c 71 e1 00      00:22:23.146  READ DMA
  c8 00 08 78 d0 60 e0 00      00:22:23.146  READ DMA
  c8 00 03 8e c7 51 e3 00      00:22:23.146  READ DMA

Error 9 occurred at disk power-on lifetime: 6120 hours (255 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 40 c9 c9 60 e0  Error: UNC at LBA = 0x0060c9c9 = 6343113

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c4 03 80 80 c9 60 e0 00      00:22:57.541  READ MULTIPLE
  ca 03 08 90 3f 60 e0 00      00:22:57.541  WRITE DMA
  ca 03 18 a0 2f 5f e0 00      00:22:57.540  WRITE DMA
  ca 03 01 a8 a5 a5 e0 00      00:22:57.540  WRITE DMA
  ef 03 45 01 00 00 a0 00      00:22:57.540  SET FEATURES [Set transfer mode]

Error 8 occurred at disk power-on lifetime: 6120 hours (255 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 37 c9 c9 60 e0  Error: UNC 55 sectors at LBA = 0x0060c9c9 = 6343113

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 80 80 c9 60 e0 00      00:22:43.050  READ DMA
  c8 00 80 00 c9 60 e0 00      00:22:43.049  READ DMA
  c8 00 80 80 c8 60 e0 00      00:22:43.047  READ DMA
  c8 00 80 00 c8 60 e0 00      00:22:43.044  READ DMA
  c8 00 80 80 c7 60 e0 00      00:22:43.043  READ DMA

Error 7 occurred at disk power-on lifetime: 5085 hours (211 days + 21 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  01 51 0a d9 dc bb e6  Error: AMNF 10 sectors at LBA = 0x06bbdcd9 = 112975065

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 80 63 dc bb e6 00      12:51:39.256  READ DMA
  ca 00 08 00 3f 5e e0 00      12:51:39.256  WRITE DMA
  c8 00 80 e3 db bb e6 00      12:51:39.254  READ DMA
  ca 00 18 f8 95 5e e0 00      12:51:39.253  WRITE DMA
  c8 00 80 63 db bb e6 00      12:51:39.249  READ DMA

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

The above only provides legacy SMART information - try 'smartctl -x' for more

